Effect of short-term storage on phenolic content,o-diphenolase and peroxidase activities of cut yam tubers (Dioscorea sp)

The effect of short-term storage on the protein, phosphorus and phenolic content as well as peroxidase and o-diphenolase activities of cut, harvested Jamaican yam (Dioscorea sp) tubers (D rotundata. D alata and D cayenensis) was studied. There was an initial increase in the total phenolic content up to the third week of storage followed by a gradual decrease to the sixth week. Phenolic content was found to be highest in D cayenensis followed by D rotundata and D alata. The activities of peroxidase (EC 1. 11. 1. 7) and o-diphenolase (EC 1. 10.3.1) increased steadily up to the third week of storage and thereafter decreased to the fifth week. The intensity and rapidity of browning in tubers when cut, correlated very closely with the tuber o-diphenolase and phenolic content levels while the onset of rotting correlated with the peroxidase activity levels in the species studied.     

Entrepreneurship in an Unstable Environment: The Experience of the Occupied Territories

The research aims at exploring the relationship between small business enterprises and their environments through an empirical investigation of the methods and strategies adopted by a number of industrial firms operating in the West Bank and the Gaza Strip in response to the exigencies and challenges of the uprising in the occupied territories in order to survive. Though the problems faced by the industrial sector as a result of the unique situation in the areas are almost unparalleled in other parts of the world, it has been possible to gain fresh insight into the dynamics of the environmental factors and their impact on organizational structure and function. Despite innumerable obstacles, the industrial sector has achieved a reasonable degree of growth.     

An assessment of the θ-projection method for the representation and extrapolation of creep data for a 1%Cr, 12%Mo, 14%V steel tested at 565°C

Constant stress creep data for a wrought 1%Cr, $\text{1}\text{2}\text{\%}\text{Mo}$, $\text{1}\text{4}\text{\%}\text{V}$ steel obtained from six tests carried out at 565°C have been fitted and extrapolated using the θ-projection method. Creep curves for high stresses were fitted well, but curves extrapolated to stress levels below those used in the θ-projection did not represent well the available data for primary-secondary creep. To enable a satisfactory extrapolation of results, it was found necessary to redefine the failure condition to be less sensitive to the shape of the latter sections of the tertiary creep curve. This was achieved by defining lifetime as the point on the curve at which the strain rate reached a fixed multiple of the creep rate at half the rupture time. The extrapolated data compare well with the results of tests carried out independently on a cast 1%Cr, $\text{1}\text{2}\text{\%}\text{Mo}$, $\text{1}\text{4}\text{\%}\text{V}$ steel. The extrapolation procedure not only predicts the ‘knee’ in the log stress-log lifetime curve but allows extrapolation of lifetimes by over a factor of thirty. In addition, acceptable predictions have been made of constant load experimental data.     

Morphological responses in thermally conditioned linear low density polyethylene

An octene-modified linear low density polyethylene has been used to examine the mechanisms involved during thermal annealing. Annealing temperatures ranged from 60 to 100°C. Annealing results in crystallinity increments and these respond to two concurrent effects. One involves the segregation from crystalline regions of low molecular weight moieties in the polymer's molecular weight distribution; the other is lamellar thickening, leading to the formation of more highly perfected crystalline domains. In the present polymer, the two effects were found to be in balance at annealing temperatures near 80°C leading to the optimum distribution of crystalline regions in the amorphous portions of the polymer. The effect of thermal conditioning on mechanical properties of the polymer was illustrated in terms of the initial modulus and the polymer's yield strength. The twin mechanisms of molecular fractionation and lamellar thickening were found to influence both of the mechanical property parameters.     

A novel silicon Schottky diode for NLTL applications

The design and simulation of a novel silicon Schottky diode for nonlinear transmission line (NLTL) applications is discussed in this paper. The Schottky diode was fabricated on a novel silicon-on-silicide-on-insulator (SSOI) substrate for minimized series resistance. Ion implantation technology was used as a low-cost alternative to molecular beam epitaxy to approximate the delta (/spl delta/) doping profile, which results in strong nonlinear CV characteristics. The equivalent circuit model of the Schottky diode under reverse bias conditions was extracted from the S-parameter measurement performed on the diode. The measured CV characteristics show strong nonlinearity, the junction capacitance varies from 182 to 47.5 fF as the reverse bias voltage is varied from 0 to -5 V. A parasitic inductance of 40 pH was measured for the silicon Schottky diode, which is much smaller than a comparable sized GaAs Schottky diode. This small inductance is an advantage for the silicon Schottky diode offering improvement in the silicon NLTL performance.     

Chromosome comparison between populations of the collared peccary, Tayassu tajacu, raised in captivity

The collared peccary (Tayassu tajacu) is widely distributed over the American continent, being found from the south of the USA to the north of Argentina. In Brazil, it is spread all over the country, being one of the potential species to be raised in captivity. Therefore, the cytogenetic techniques could be a potential tool for reproductive monitoring of animals raised in captivity, mainly when destined for commercial purposes. This study had the objective of determining the chromosome number of two populations raised in captivity and characterizing them by GTG banding. For this purpose, an analysis was made of mitotic metaphases obtained from lymphocyte cultures made from blood samples of 11 animals, six of which from the Northeast and five from the North of Brazil. The results of this analysis showed the same karyotype pattern for the species (2n=30 chromosomes and NF=48), besides corresponding to the South American pattern of the species, i.e., without a translocation between autosomes 1 and 8, chromosome X acrocentric, and no differences were found between the two populations studied. However, chromosomal polymorphisms were observed compared to data from the literature on populations from North and South America.     

Pyramid collaborative filtering technique for an intelligent autonomous guide agent

This article presents an autonomous guide agent that can observe a community of learners on the web, interpret the learners' inputs, and then assess their sharing. The goal of this agent is to find a reliable helper (tutor or other learner) to assist a learner in solving his task. Despite the growing number of Internet users, the ability to find helpers is still a challenging and important problem. Although helpers could have much useful information about courses to be taught, many learners fail to understand their presentations. For that, the agent must be able to deal autonomously with the following challenges: Do helpers have information that the learners need? Will helpers present information that learners can understand? And can we guarantee that these helpers will collaborate effectively with learners? We have developed a new filtering framework, called a pyramid collaborative filtering model, to whittle the number of helpers down to just one. We have proposed four levels for the pyramid. Moving from one level to another depends on three filtering techniques: domain model filtering, user model filtering, and credibility model filtering. A new technique is filtering according to helpers' credibilities. Our experiments show that this method greatly improves filtering effectiveness. © 2007 Wiley Periodicals, Inc. Int J Int Syst 22: 1065–1082, 2007.     

CONTEXTUALIZING LEARNING OBJECTS USING ONTOLOGIES

Educational research over the past three years has intensified such that the context of learning resources needs to be properly modeled. Many researchers have described and even mandated the use of ontologies in the research being conducted, yet the process of actually connecting one or more ontologies to a learning object has not been extensively discussed. This paper describes a practical model for associating multiple ontologies with learning objects while making full use of the IEEE LOM specification. The model categorizes these ontologies according to five major categories of context based on the most popular fields of study actively being pursued by the educational research community: Thematic context, Pedagogical context, Learner context, Organizational context, and Historical/Statistical context.     

A hybrid technique of modeling of cracks using displacement discontinuity and direct boundary element method

A hybrid technique to model two dimensional fracture problems which makes use of displacement discontinuity and direct boundary element method is presented. Direct boundary element method is used to model the finite domain of the body, while displacement discontinuity elements are utilized to represent the cracks. Thus the advantages of the component methods are effectively combined. This method has been implemented in a computer program and numerical results which show the accuracy of the present method are presented. The cases of bodies containing edge cracks as well as multiple cracks are considered. A direct method and an iterative technique are described. The present hybrid method is most suitable for modeling problems involving crack propagation.